W4MQ Keyboard Commands

W4MQ client Keyboard Shortcuts help you move around in the application without using a mouse. 

Please go to the end of the file for otherwise undocumented commands that we have discovered.

===============

AM Mode – A

Select Rotator Display – B

CW Mode – C

Show Login display – D

Sets TX = RX in Split Mode        – E

FM Mode – F

Select RF Gain – G

Help Documentation – H

Low IF Filter – I

CW Speed – K

LSB Mode – L

Select MIC Gain –  M

Toggle Notch – N

Toggles Noise Reduction – O

toggle Power Levels – P

Toggle RX EQ  – Q

Toggles Repeater Offset – R

Toggles Split Mode – S

Tune Antenna – T

USB Mode – U

Select AF Gain  – V

Toggles Invert in Split Mode n – X

Toggles RIT On / Off – Y

Decreases Selected Value – <

Increases  Selected Value – >

Direct entry of Frequency – 0 through 9

Decreases AF Gain – –

increases AF Gain – +

Accepts Keyboard input – ENTER

Deletes Last Keyboard input – Backspace

Resets display and clear inputs – ESC

Sets Higher FREQ digit – Left Arrow

Sets Lower FREQ digit  – Right Arrow

Increase FREQ – Up arrow

Decrease FREQ – Down arrow

Direct Entry of Frequency Direct entry of selected parameters  – 1

Toggle Attenuator – SHIFT+A

Toggles Filter BW UP  – SHIFT+F

High IF Filter – SHIFT+I

Toggles AGC Levels – SHIFT+O

Toggles the preamp on and off – Shift+P

Toggles TX EQ – SHIFT+Q

Select Filter 1 – SHIFT+1

Select Filter 2 – SHIFT+2

Select Filter 3 – SHIFT+3

Select Filter 4 – SHIFT+4

Select Filter 5 – SHIFT+5

Select Filter 6 – SHIFT+6

Select Filter 7 – SHIFT+7

Select Filter 8 – SHIFT+8

Select filter 9 – SHIFT+9

Select Filter 10 – SHIFT+10

Toggle RX Antenna – CTRL+A

Keyboard input of Azimuth – CTRL+B

Logoff – CTRL+D

toggles Filter BW down – CTRL+F

Select RF Gain for Keyboard input – CTRL+G

Select CW Speed for Keyboard entry – CTRL+K

Logon – CTRL+L

Select MIC gain for keyboard entry – CTRL+M

Clear NetMeeting buffer – CTRL+O

Select Power for Keyboard entry – CTRL+P

Select Volume for Keyboard Entry – CTRL+V

Select Password for Keyboard Entry – CTRL+W

Select logon callsign for Keyboard input – CTRL+X

Select 1Hz Digit – CTRL+1

Select 10Hz Digit – CTRL+2

Select 100 Hz Digit – CTRL+3

Select 1 kHz Digit – CTRL+4

Select 10 kHz Digit – CTRL+5

Select 100 kHz Digit – CTRL+6

Select 1 mHz Digit – CTRL+7

Select 10 mHz Digit – CTRL+8

Select 160 M – ALT+1

Select 80M – ALT+2

Select 40M – ALT+3

Select 30M – ALT+4

Select 20M – ALT+5

Select 17M – ALT+6

Select 15M – ALT+7

Select 12M – ALT+8

Select 10M – ALT+9

Select 6M – ALT+0

Select 2M – ALT+-

Select 70CM – ALT++

Select 17M – ALT+6

Exit Application – ALT+X

Undocumented Commands

Cycling through stored memories.  If you have stored memories using the W4MQ software, you can use this command to shift through the memories 1 through 10:CTRL+downArrow and CTRL+UpArrow

 

 

Leave a Reply